PLUMBING ESSENTIALS: A PREREQUISITE FOR INSTALLING A BATHTUB

Plumbing Essentials: A Prerequisite for Installing a Bathtub

Plumbing Essentials: A Prerequisite for Installing a Bathtub

Blog Article

Book Service

We have stumbled upon this great article on A Step-by-Step Guide to Installing a Bathtub directly below on the net and think it made good sense to write about it with you on my blog.


A Step-by-Step Guide to Installing a Bathtub
Installing a bathtub isn't specifically rocket science, however it does need solid plumbing, carpentry, and in some cases, tiling skills. Replacing an old bathtub with a new one is additionally a moderately difficult job. If the old tub is conveniently accessible, the task can move speedily; if you need to open a wall to remove the old tub as well as place the new bathtub, the job is much harder. In either instance, the project is within a home handyman's skills, although you will certainly need an assistant to move out the old bathtub and also set in the new one. Make certain you have actually certified on your own for the job and also fit attempting it. As opposed to hiring a specialist to take over a halfway-completed task, it is better to take into consideration utilizing one before you begin. Chances are you may require a professional plumber to make tube links.
This write-up will certainly help you install a new tub in your restroom if you have actually already acquired a new tub and don't need to transform the plan of your previous water pipelines.
Your devices and product checklist should consist of the following:
  • New Tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipe Caps


  • Preparing for the Installment


    First of all, the supporting structure provided with the bathroom must be fitted (if needed) according to the manufacturer's directions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to ensure that if the faucet includes a plastic washer, it is fitted in between the bathroom and also the taps. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets unit to prevent strain on the tub.
    Fit the adaptable faucet adapters to the bottom of both taps utilizing 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet via the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you utilize all of the provided washers.
    Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to currently be ready to be suited its final placement.

    Removing Old Touches


    If you need to replace old faucets with brand-new ones as a part of your setup, after that the first thing you ought to do is disconnect the water system. After doing so, turn on the taps to drain any water staying in the system. The procedure of eliminating the existing faucets can be fairly troublesome because of the restricted accessibility that is commonly the case.
    Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the faucets. Have a fabric prepared for the continuing to be water that will certainly come from the pipes. As soon as the supply pipelines have actually been eliminated, make use of the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary faucets from turning during this process. Once the taps have actually been removed, the holes in the bath/basin will have to be cleaned up of any old sealing compound.
    Before carrying on to fit the new taps, contrast the pipeline links on the old faucets to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the new faucets to fit.

    Installing the Tub


    Making use of both wood boards under its feet, position the bath tub in the needed position. The wood boards are useful in uniformly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto 4 tiny points.
    The following objective is to guarantee that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as changing the feet on the bathtub till the level reviews level.
    To install faucets, fit all-time low of the outermost versatile faucet connector to the suitable supply pipe by making a compression sign up with; then do the very same for the other faucet.
    Turn on the water system and check all joints and new pipework for leakages and also tighten them if required. Fill up the tub and additionally examine the overflow outlet and also the normal electrical outlet for leaks.
    Finally, take care of the bathroom paneling as explained in the producer's instruction manual. Tiling and also securing around the bath tub must wait up until the tub has been utilized a minimum of once as this will certainly resolve it into its final placement.

    Suitable New Taps


    If the tails of the new taps are plastic, after that you will need a plastic connector to avoid damages to the string. One end of the port fits on the plastic tail of the faucet and also the various other end provides a link to the existent supply pipes.
    If you require to fit a monobloc, then you will call for lowering couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
    Next off, place the tap in the installing hole in the bath/basin making certain that the washers remain in location between the faucet and also the sink. Safeguard the faucet in place with the producer given backnut. Once the tap is securely in place, the supply pipes can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with regular tap connectors. The former kind ought to be attached to the faucet finishes first, tightening just by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.

    Tiling Around the Bathtub


    In the location where the bath satisfies the tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move sufficient to fracture an inflexible seal, triggering the water to penetrate the wall surface in between the bath and the tiling, bring about problems with wetness and feasible leakages to the ceiling listed below.
    You can select from a selection of coloured sealers to blend in your components and fittings. They are offered in tubes and cartridges, and can securing gaps approximately a width of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to always fill up the bath tub with water before sealing, to allow for the activity experienced when the bathtub is in use. The sealant can break rather very early if you do not take into account this activity prior to securing.
    Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also easily offered on the marketplace. It is suggested to fit the tiles making use of water-resistant or water-proof adhesive and also cement.

    Bathtub Installation


    How Important Is A Bathtub To Your Home?


    High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.


    Install Piping Before Tub


    You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.


    Position the Tub


    Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.



    NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.


    Assemble Drain Connections


    Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.


    Place a Pipe For the Shower Head


    First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.


    Attaching Hot and Cold Water Lines


    Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.


    Install the Spout


    Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.



    NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.


    Check For Leaks


    Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.


    estore the Bathroom Wall


    Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

    https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/


    How to Install a Bathtub Yourself

    I ran across that post about How to Install a Bathtub when doing a search on the search engines. Do you know another individual who is looking into How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Take a moment to promote it. Many thanks for taking the time to read it.


    Need assistance? Call.

    Report this page